Part Number: 901.423.421.00
Clutch cable sleeve for 911 and 912 models. Years 1965-1969.

Part Number: 644.501.083.01
2-Piece engine shelf piece for 356 T1/T2 models. Years 1956-1959. This is sold as a set.

Part Number: SMC.Nail
Upholstery Nail Set for all models. This hard to find nail set is used throughout the car and contains 20 pieces.

Part Number: 901.613.915.00
Hard to find horn contact ring for 911 and 912 models. Years 1965-1973.

Part Number: BMR13B
This brushed, billeted aluminum roll bar mount is quick release for your fire extinguisher. It is approved by most race- sanctioning bodies and clubs including, NHRA, IHRA, NMCA, NMRA, NSRA and MTRA. It is meant to be used with a band clamp concurrently. This mount will fit roll bars that are 6.3" in circumference and is 2" in diameter.

Part Number:978-09297582-9-9
The 914 and 914-6 Porsche, A Restorer's Guide to Authenticity III takes a part-by-part, year-by-year approach to what an owner or prospective buyer should look for when evaluating a 914 Porsche. For each year, from 1970 through 1976, the author examines every change, documented or not, of each model – and now including major mechanical components. Included are the most accurate and comprehensive chassis number and color/upholstery listings anywhere.

Part Number: 901.107.801.01
Cast aluminum oil cooler thermostat for 2.0S-2.2S motors. Suitable for 911S (1969-1971) and 914/6GT.

Part Number: SMC.356.049
Fuel tank banjo kit for 911/912 models. Years 1965-1973. Steel banjo kit finished in cad yellow with correct M14 banjo bolt and 8 mm tube size. includes two copper washers.

Part Number: SMC.810.06
Hazet 6-piece set toolset that includes (4) Slotted Screwdrivers and (2) Phillips Screwdrivers. Each tool is the Hazet Blue color with a non-slip 3-component handle for high power transmission. The tools also contain a hanging hole in the handle for easy storing and matte chrome plated blade with a burnished tip.

Part Number: SMC.000.311
Complete your OUTLAW project with this chrome nerf bar set! Interchangeable for the front or the rear. For replica cars only. This set of two bars can be used in the front or rear to replace the stock bumper and bracket. These are steel chrome.

Part Number: SMC.000.310
Complete your OUTLAW project with this chrome nerf bar set! Interchangeable for the front or the rear. For replica cars only. This set of two bars can be used in the front or rear to replace the stock bumper and bracket. These are steel chrome.

Part Number: 911.522.063.40
Black-Black high-quality reproduction rear seat strap set for 911 and 912 models. Years 1974-1989. Embossed leather with male snaps. These straps are hand made in Europe and measures 3.75 inches or 95mm. Sold as a pair and suitable for coupes and targas.

Part Number: 911.522.063.00
Black-Black high-quality reproduction rear seat strap set for 911 and 912 models. Years 1974-1989. Embossed leather with female snaps. These straps are hand made in Europe and measures 7.5 inches or 19.1 cm. Sold as a pair and extensions sold individually.

Part Number: 901.522.063.40
Black-Tan high-quality reproduction rear seat strap set for 911 and 912 models. Years 1965-1973. Embossed leather with male snaps. These straps are hand made in Europe and measures 3.75 inches or 95mm. Sold as a pair and suitable for coupes and targas.

Part Number: 901.522.063.20
Black-Tan high-quality reproduction rear seat strap set for 911 and 912 models. Years 1965-1973. Embossed leather with female snaps. These straps are hand made in Europe and measures 7.5 inches or 19.1 cm. Sold as a pair and extensions sold individually. Upholstery nails included!

Part Number: SMC.352.966.SET
Rebuilt rear "wide L" caliper set for 911/912 (1967-1968) models with vented brake rotors. Completely restored by the most respected name in brakes, PMB Performance.

Part Number: 944.503.513.00
Spoiler bracket for 944 models. Years 1983-1991.

Part Number: 911.559.107.00
Securing plate for 2.4 emblems on the rear grille. Years 1972-1973. Please note this is to just secure the emblem to the grille and doesn't include the emblem. Please see part number 911.559.015.00 for emblem

Part Number: 901.375.031.00
Transmission support with mounts for 911 and 912 (1965-1970) models.

Part Number: 901.551.116.50
Aluminum door threshold for 911S and 911E. These were introduced in 1967 with the 911S model and used up to 1973. We also have the rivets to secure them (#999.591.550.40).

Part Number: 901.551.115.50
Aluminum door threshold for 911S and 911E. These were introduced in 1967 with the 911S model and used up to 1973. We also have the rivets to secure them (#999.591.550.40).

Part Number: 911.559.142.04
Black end cap for left front or right rear rocker trim on Carrera and Turbo models.

Part Number: 911.559.141.04
Black end cap for right front or left rear rocker trim on Carrera and Turbo models.

Part Number: 901.615.615.20
Door light switch washer for 911, 912 and 930 models.

Part Number: 914.423.283.00
Accelerator cables stop plate for 914 (1970-1976) models.

Part Number: SMC.356.50
Complete rear seat bottom for 356 T5 models. Years 1960-1962.

Part Number: 911.512.010.56
Rear steel deck lid for 911 models (1974-1989).

Part Number: SMC.448.01
Porsche 'Pasha' (Pascha) flannel material for Porsche 911, 924 and 928 models from 1978 through 1984.

Part Number: SMC.448.00
Excellent, German quality reproduction of the very popular Pepita cloth for early 911, 912, 914 and even the 356C models.

Part Number: SMC.448.03
Porsche 'Tartan' material for Porsche 911, 924 and 928 models 1975-1980.

Part Number: SMC.448.02
Porsche 'Pinstripe' flannel material for Porsche 911, 924, 928 and early 964 models 1977-1979 and 1985-1990.

Part Number: 996.355.577.40
Brake booster vacuum line with the check valve for 911 Carrera (1999), and Boxster (1997-1999) models.

Part Number: SMC.503.121
Fiberglass front lower valance for 914 models. Years 1970-1976.

Part Number: 914.512.913.00
Rear trunk lock for 914 models. Years 1970-1976. Please note this is a used part.

Part Number: SMC.000.500
Basket Weave Material. Sold per meter.

Part Number: 911.612.017.00
Engine wire harness for Motorola Generators for 911 models. Years 1970-1971. This is a complete engine harness that connects to 14 pole male connectors on the engine fuse panel. With original color-coded wiring. The harness will exactly fit like the original. Wire tube, and oil resistant tape as the original. Terminals have rubber sleeves. The harness comes with detailed connection instructions. With new 14 pole female connector and rubber cable entry block, new grommet for the alternator, new rubber boots on alternator connection.

Part Number: SMC.005.024
Willhoit stock cylinder heads for 356 (1950-1965) and 912 (1965-1969) models. Cast just like the original heads but using a proprietary alloy and heat treat process that will not crack. The prototypes were extensively tested on the WR engine dyno and on the street. The flow-through finning allows for cooling that is impossible with a CNC machined head.

The smaller DR6EA plug is 12mm x ¾” reach and allows for much more material around the valves. It is a commonly used plug size and is easily available. Four new plugs are supplied with each set of heads. The stainless steel 8mm stem valves are 38mm intake and 34mm exhaust and are installed using a 5 angle valve job. The guides are silicon-bronze alloy for excellent heat transfer and long life. The port design is similar to the original, but the use of the smaller valves and guides allows for improved flow (7% on intake, 3% on exhaust).

Special bead lock Chromoly retainers are matched to the double springs and are good for 7k RPM and lift up to .525 without coil bind. The air injection bosses were retained to allow easy installation of a head temp sensor for EFI. The 61.0cc matched chambers have a 30-degree bevel cut to be compatible with the later factory and aftermarket piston and cylinder kits. Intake and exhaust ports are the larger SC and 912 version.

Test on our in house Superflow 902S dyno shows an improvement over even the latest 356C/912 heads. Improvements compared to earlier heads will be more. Completely assembled and ready to install and run. The WR Standard Cylinder Heads are a perfect replacement for early and late 356 and 912 engines.

Part Number: 911.612.002.10
Complete main-harness with original color-coded wiring for LHD 911 (1971-1973) models. Runs from front fuse-box to dashboard. The harness will exactly fit like the original. Wire tube, and oil resistant tape as the original. Terminals have rubber sleeves. The harness comes with detailed connection instructions.

Part Number: 911.612.001.10
Complete tunnel harness with original color-coded wiring for LHD 1971 911 models. Runs from front fusebox/gauges through the tunnel to the engine bay. The harness will exactly fit like the original. Wire tube, and oil resistant tape as the original. Terminals have rubber sleeves. The harness comes with detailed connection instructions. 2 new 6 pole male connector and 1 x 14 pole female connector included.

Part Number: 901.628.753.21
Washer Fluid Reservoir bushing for 911 and 912 models. Year 1966-1967. Number 4 on the diagram.

Part Number: 996.642.591.00
Porsche Classic Communication Management radio for 996 (1998-2005) and 986 (1997-2004) models with 2 din slot. This newly released unit combines the analog past with present tech. With its unique, original look complete with Porsche lettering, the PCCM blends seamlessly into the vehicle interior. In addition to touchscreen operation via a 7-inch display, modern functions such as Apple CarPlay and Andriod Auto have now become part of the PCCM. Like its predecessor, the PCCM also features additional onboard navigation and can receive SiriusXM® satellite radio. Route guidance is available in 2D, 3D, and as a basic arrow view. Includes the associated map material SD card and the SiriusXM adapter cable can also be ordered.
Media can be played back via SD card, USB, AUX, and Bluetooth®. In addition to the features already mentioned, Apple CarPlay and Andriod Auto can also be used for media playback, navigation, and telephone calls.
Please note: Porsche Classic recommends having the installation carried out professionally by your Porsche Partner - Only for the USA and Canada, please contact sales for the European version.

Part Number: 911.721.002.05
Car Bone original black tool bag for 911 models. Years 1974-1989. This reproduction tool bag is made of leather and period correct for all g-model cars.

Part Number: 993.424.075.01.8YR
Black gearshift knob for 993 models. Years 1994-1998.

Part Number: 901.108.720.02
Relay lever for 911 and 912 models. Years 1965-1969.

Part Number: SMC.VISOR.FS
Final sale SMC visor set

Part Number: 944.347.447.02
Power steering line from pump to rack for 924, 944 and 968 models (1985-1995).

Part Number: 901.531.305.20
Door hinge pin for 911, 912, 930 and 912E models (1965-1989). Two per door.

Part Number: 951.116.085.00
Clutch release fork for 944 models. Years 1986-1989. This part is no longer made by Porsche and is now available!

Part Number: 914.424.016.00K
Chrome gear shift lever for 911 (1965-1972), 912 (1965-1969) and 914 (1970-1976) models. This is not available through Porsche and a replacement lever only. Installation does require the use of epoxy. This does not include the lower shift quadrant.

Part Number: 999.215.027.03
Front lower wheel cylinder banjo bolt for 356 Pre-A, 356A, 356B and 911 models (1950-1986). Two required.

Part Number: SMC.CAR.COVER
Beautiful 356 indoor car cover for all 356 models. Years 1950-1965. Reutter logo on hood and lower right side (see pictures for more details). The cover, which is precisely tailored to the body shape, consists of extremely breathable 4-way stretch wicking jersey (88% polyester / 12% spandex) PFOS free and antibacterial, extremely elastic with high return value and washable at 40 ° C. It forms almost the second skin and absolute protection. The design is colored, not printed. The absence of material damage on the inside completely avoids leaving lint on a fabric roof, as well as condensation and moisture.

Part Number: 901.551.419.00
Hard to find early 911/912 (1965-1968) stainless steel carpet trim plate. Two needed per car.

Please see part number SMC.551.001.00 for needed screw set (sold separately)

Part Number: 901.343.754.01
Mounting plate for the front sway bar. Fits 911 and 912 (1965-1973) models.

Part Number: 993.637.049.02
Remote key immobilizer control unit for 993 models.

Part Number: SMC.311.906
Fuel Pump Connector w/ Rubber Boot Set that includes fuel pump connector, fuel pump connector boot and 3 female terminals.

Part Number: 911.612.016.00
Engine wire harness for Bosch Generators for 911 models. Years 1970-1971. This is a complete engine harness and connects to 14 pole male connector on engine fuse panel. With original color coded wiring. Harness will exactly fit like the original. Wire tube, and oil resistant tape as original. Terminals have rubber sleeves. Harness comes with detailed connection instructions. With new 14 pole female connector and rubber cable entry block, new grommet for alternator, new rubber boots on alternator connection.

Part Number: 911.612.050.00
Wire Harness for 3 Pin CDI Box for 911 and 930 models. Years 1969-1977. Harness from CDI box to distributor/ignition coil, rubber grommet, and a high quality braided screen with an exact replica boot & 3 pole connector. The wiring is shielded and runs through the braiding (not next to it) As original colored wiring. Original neoprene terminal sleeves used, (no shrink tube!) This harness is gasoline, oil, battery acid, and engine coolant resistant. Handmade in Holland, concourse quality!

Part Number: SMC.602.702.00
CDI rubber boot connector set for 911 and 930 models. Years 1969-1989. 100% as original, the rubber boot even has the original markings! Made in Germany of very high quality oil and heat resistant rubber. Comes with chassis part and female crimp terminals.

Part Number: 911.424.047.00
Black lever gear shift lever boot for 911 and 930 models. Years 1965-1989. Can be used to replace 911.424.181.01

Part Number: 911.803.198.01
3 point retractable seat belt for 911, 924, 928 , and 944 models. Years 1965-1983. This made in Germany seat belt is TÜV approved and fits both driver and passenger sides.

Part Number: SMC.007.01
Carbon fiber front bumper for 911 Turbo S (1973) models. 9” flares.

Part Number: 901.612.330.00
Six pole relay plug connector for 911, 924S, 944 and 968 models.

Part Number: 901.101.195.00
Crankcase sleeve for 911 models. Years 1965-1998

Part Number: 986.424.049.01
Securing clip for Boxster models. Years 1997-2004.

Part Number: 999.166.077.02
Securing Clip for Boxster models. Years 1989-2005.

Part Number: 999.192.352.50
V-belt for 964 models. Years 1989-1994.

Part Number: 993.110.118.00
Hose elbow for 993 models. Years 1994-1998.

Part Number: 964.351.803.04
Front brake protective plate for the left side of 993/Turbo (1990-1998) models.

Part Number: SMC.501.034
Right front inner fender bracket for 911 and 912 models. Years 1969-1973.

Part Number: SMC.501.033
Left front inner fender bracket for 911 and 912 models. Years 1969-1973.

Part Number: 901.332.232.00
Rear stub axle for 911 models. Years 1968-1973.

Part Number: 928.618.104.00
Rear window wiper relay for 911 and 928 models. Years 1978-1995.

Part Number: 911.731.013.08
Rectangular small chrome mirror, for the left side. Gasket included. Fits 911 models (1972-1973). This part supersedes part number 911.731.014.06. ** Please note that the High-Quality Reproduction option includes just hardware. Gasket and bolts are supplied with the Genuine version. Please do not over tighten during installation as damage could occur if over tightened. Please see part number 911.731.129.00 for mirror base gasket